山东装载机轮胎更换的方法是啥？-凯发k8官网下载

1.启动山东装载机，就近寻找一块比较平坦开阔的场地，压下动臂升降杆，利用动臂支承使前轮离地，然后用支架支撑在闪桥靠近爆胎的一侧，并将后轮楔好。shandong boot loader, find the nearest one site is relatively flat and open, under the pressure of the boom lifting rod, the movable arm supporting the front wheels off the ground, and then use the support in the bridge near the tire side flash, and rear wheel wedge.

2.利用撬杠等等工具，拆卸挡圈及锁圈然后检查轮胎衬垫与轮辋外表面是否粘连。若发生可撤掉支撑物，使山东装载机在短距离内慢速往复运行，直至衬垫与轮辋外表面脱离；严禁转向和高速行驶，以免损坏内胎。然后，前轮重新支撑起来。use a crowbar, and removing the retainer ring lock ring and then check the tire and rim liner outer surface adhesion. if there can be removed support, make shandong loader running slow reciprocating within a short distance, until the liner and the outer surface of the rim from the forbidden; steering and high speed, so as to avoid damage to the tube. then, the front wheel to prop up.

3.将山东装载机内、外胎的相对位置作好标记，以便查找、清除异物和修补轮胎。the relative position of shandong, the loader tire mark, in order to find and remove foreign bodies and tire repair.

4.利用撬杠等工具，将山东装载机轮胎从轮辋上拆下。注意，动作要轻柔配合要默契，避免被轮胎砸伤，并且要保护好气门嘴。use the crowbar and other tools, will shandong loader from tire rim removed. note that the action should be gentle with the tacit understanding, to avoid being injured and protect the tire, aerobic door mouth.

5.山东装载机外胎被钉子等细长异物扎伤后，若表面无明显创口或创口较小，则此外胎可继续使用(因为装载机轮胎属低压胎，且运行速度比较慢)；若创口较大，则必须进行修补(因为机器运行时，轮胎受挤压磨擦，时间一长就会损坏内胎，甚至创口越来越大、内胎突出，造成轮胎报废)。shandong tire loader is slender nail foreign body after injuries, if the surface has no wound or the wound is small, the tyre can continue to use (because the loader is a low pressure tire tread, and the running speed is relatively slow); if the wound is large, it must be repaired (because when the machine is running, the tire friction would be squeezed, long time tube damage, even more and more prominent, the wound tube, causing scrap tire).

6.若是新内胎，必须将气门嘴底部的螺栓拧紧，以防漏气；然后将外胎内腔的异物清除，并撒入适当的滑石粉，涂抹均匀。为了使衬垫与内、外胎贴紧，在山东装载机装入内胎后应给内胎适当充气，再塞入衬垫。if the new tube, must tighten valve at the bottom of the bolt, to prevent leakage; then the tyre cavity foreign body removal, and sprinkle with appropriate talcum powder, evenly. in order to make the inner liner and tyre tightly, loader into the tube in shandong should give appropriate air into the liner tube, then.

7.将山东装载机轮胎装到轮辋上，装上锁圈、挡圈；安装过程中要保护好气门嘴。shandong loader tires mounted on the rim, fit a lock ring and the retainer ring; the installation process to protect the aerobic door mouth.

8.用车载空压机给山东装载机轮胎充气。charging of shandong loader tire with vehicle air compressor.

9.压下动臂升降杆，取出支架；至此山东装载机换胎完毕，整个过程大约需要50min。更换后轮胎时，则需要另一台山东装载机或者其他起重设备辅助，将后轮胎支撑起来，其他程序则与更换前轮胎相同。out of the bracket arm lifting rod, under pressure; thus shandong loader tires is completed, the entire process takes about 50min. replacement of the tires, you need another shandong loader or other lifting equipment auxiliary, the rear tire support, other procedures and replacement of the same tire.